And in addition, the config.log found in /build.

Fred

De: "Carl Hetherington via DCPomatic" <dcpomatic@carlh.net>
À: dcpomatic@carlh.net
Envoyé: Vendredi 15 Mai 2015 21:32:50
Objet: Re: [DCP-o-matic] <DKIM> Re: dcpomatic on Raspberry Pi / Raspian
Hi Fred,
Just the output of the waf command would be enough, probably.  If you do
./waf | tee log
then send the file "log" that should contain it.
Regards,
Carl
On Fri, 15 May 2015, Fred via DCPomatic wrote:
> Ok, thanks.
>
> I've proceeded 2 runs on 3 cores. Things go relatively smoother and even faster than before (sic...).
>
> I.e: 3x100% CPU and memory goes up to >800M but never reached 1G. Power reaches a hudge 3W...!
> I can still access the Pi thru SSH to run htop. Much better...
>
> I now see only 128 elements to build with "--disable-gui" option, which makes about 30% less work to achieve assuming all files need the same delay to be built.
>
> I still get a lot of warnings about swp{b} deprecated for ARMv6 & 7.
> And finally, build went twice to 23/128 (ffmpeg_content) but failed each time at this point.
>
> Carl, can I post log files in order for you to see what's going on? what file(s)??
>
> Fred
>
>
> _____________________________________________________________________________________________________________________________________________________________________
> De: "Carl Hetherington via DCPomatic" <dcpomatic@carlh.net>
> À: dcpomatic@carlh.net
> Envoyé: Vendredi 15 Mai 2015 19:19:06
> Objet: Re: [DCP-o-matic] <DKIM> Re: dcpomatic on Raspberry Pi / Raspian
>
> You only need --target-arm on configure.
>
> ./waf clean
>
> Removes all build files.
>
> Cheers,
> Carl
>
>
> On May 15, 2015 4:47:31 PM GMT+01:00, Fred via DCPomatic <dcpomatic@carlh.net> wrote:
> >Latest news:
> >
> >It seems that up to 3 cores, processing build is Ok. May be only 2
> >cores is more secure as 3 makes memory getting a bit high, even if it
> >seems to stay behind the 1G limit.
> >4 cores is for sure too much for the Pi.
> >
> >A few more questions (as for compiling, I'm a noob...):
> >- do I need to specify again "--target-arm" for the build process?
> >- how can I flush the previous build process to start again with a
> >clean setup?
> >
> >Thanks,
> >Fred
> >
> >----- Mail original -----
> >
> >De: "Fred via DCPomatic" <dcpomatic@carlh.net>
> >À: "Carl Hetherington" <cth@carlh.net>
> >Cc: dcpomatic@carlh.net
> >Envoyé: Vendredi 15 Mai 2015 16:25:39
> >Objet: <DKIM> Re: [DCP-o-matic] <DKIM> Re: Re : Re: dcpomatic on
> >Raspberry Pi / Raspian
> >
> >
> >
> >----- Mail original -----
> >
> >De: "Carl Hetherington via DCPomatic" <dcpomatic@carlh.net>
> >À: dcpomatic@carlh.net
> >Envoyé: Vendredi 15 Mai 2015 16:15:02
> >Objet: Re: [DCP-o-matic] <DKIM> Re: Re : Re: dcpomatic on Raspberry Pi
> >/ Raspian
> >
> >Hi Fred,
> >
> >Sorry, I misunderstood. Build with
> >./waf -j1
> >to only use 1 core.
> >
> >I'll try this as soon as build fails...
> >
> >Concerning Boost, I don't remember exactly where I got this packages.
> >But I know that you had to do something in the code and asked me to
> >specify "--target-arm" to get configure passed.
> >
> >I'm starting a new test following your latest instructions:
> >sudo ./waf configure --disable-gui --target-arm => Ok
> >sudo ./waf build --disable-gui => in progress
> >
> >Thanks,
> >Fred
> >
> >
> >
> >_______________________________________________
> >DCPomatic mailing list
> >DCPomatic@carlh.net
> >http://main.carlh.net/cgi-bin/mailman/listinfo/dcpomatic
> >
> >
> >
> >------------------------------------------------------------------------
> >
> >_______________________________________________
> >DCPomatic mailing list
> >DCPomatic@carlh.net
> >http://main.carlh.net/cgi-bin/mailman/listinfo/dcpomatic
>
>
> _______________________________________________
> DCPomatic mailing list
> DCPomatic@carlh.net
> http://main.carlh.net/cgi-bin/mailman/listinfo/dcpomatic
>
>
>
_______________________________________________
DCPomatic mailing list
DCPomatic@carlh.net
http://main.carlh.net/cgi-bin/mailman/listinfo/dcpomatic